column 7 of the hazardous materials tablemost awkward queer eye moments

B68 Sodium must be in a molten condition when loaded and allowed to solidify before shipment. When a special provision specifies packaging or packaging requirements -, (1) The special provision is in addition to the standard requirements for all packagings prescribed in 173.24 of this subchapter and any other applicable packaging requirements in subparts A and B of part 173 of this subchapter; and. 56 A means to interrupt and prevent detonation of the detonator from initiating the detonating cord must be installed between each electric detonator and the detonating cord ends of the jet perforating guns before the charged jet perforating guns are offered for transportation. Packages containing mixtures with not less than 90% by mass, of phlegmatizer need not bear a POISON subsidiary risk label. 385 Notwithstanding the provisions of 177.834(l) of this subchapter, cargo heaters may be used when weather conditions are such that the freezing of a wetted explosive material is likely. However, the hazard label corresponding to the hazard class or division may be substituted for the marking. N88 Any metal part of a UN pressure receptacle in contact with the contents may not contain more than 65% copper, with a tolerance of 1%. Flammable components are flammable liquids and liquid mixtures, flammable solids and solid mixtures or flammable gases and gas mixtures meeting the following criteria: (1) A flammable liquid is a liquid having a flashpoint of not more than 93 C (200 F); (2) A flammable solid is a solid that meets the criteria in 173.124 of this subchapter; or. For the purpose of this special provision, vehicles are self-propelled apparatus designed to carry one or more persons or goods. TP37 IM portable tanks are only authorized for the shipment of hydrogen peroxide solutions in water containing 72% or less hydrogen peroxide by weight. d. Except for transportation by aircraft, neutron radiation detectors and radiation detection systems containing such detectors transported in accordance with paragraph a of this special provision are not subject to the labeling and placarding requirements of part 172 of this subchapter. Based on the volatility class determined by using ASTM D 439 and the Reid vapor pressure (RVP) of the particular gasoline, the maximum lading pressure and maximum ambient temperature permitted during the loading of gasoline may not exceed that listed in Table I. N45 Copper cartridges are authorized as inner packagings if the hazardous material is not in dispersion. c. The motor carrier must maintain a satisfactory safety rating as prescribed in 49 CFR part 385. 336 The use of UN1H1 drums, UN3H1 jerricans, and UN6HA1 composite packagings which meet the requirements of part 178 of the HMR at the Packing Group I or II performance level. TP46 Portable tanks in sodium metal service are not required to be hydrostatically retested. d. A chemical under pressure with components meeting the properties of: Class 1 (explosives); Class 3 (liquid desensitized explosives); Division 4.1 (self-reactive substances and solid desensitized explosives); Division 4.2 (substances liable to spontaneous combustion); Division 4.3 (substances which, in contact with water, emit flammable gases or toxic gases); Division 5.1 (oxidizing substances); Division 5.2 (organic peroxides); Division 6.2 (Infectious substances); or, Class 7 (Radioactive material), must not be offered for transportation under this description. N25 Steel single packagings are not authorized. There must be no hazardous effects outside the package such as disruption of the package, metal fragments or a receptacle which passes through the packaging. 8 A hazardous substance that is not a hazardous waste may be shipped under the shipping description Other regulated substances, liquid or solid, n.o.s., as appropriate. Transportation by vessel in IBCs is prohibited. Multiple provisions can be listed in this column. 74 During transport, this material must be protected from direct sunshine and stored or kept in a cool and well-ventilated place, away from all sources of heat. 159 This material must be protected from direct sunshine and kept in a cool, well-ventilated place away from sources of heat. 163 Substances must satisfactorily pass Test Series 8 of the UN Manual of Tests and Criteria, Part I, Section 18 (IBR, see 171.7 of this subchapter). (v) The box must be constructed from high-density polyethylene in the density range 0.950-0.962, and be capable of holding liquid when in the upright position. not more than 0.1 mL/hour per 30 mL inner packaging at 20 C (68 F) produced from gradual decomposition. Those "other methods" for determining authorized packaging are identified at 173.24 (c) (1) (ii). 49 Mixtures of solids that are not subject to this subchapter and corrosive liquids may be transported under this entry without first applying the classification criteria of Class 8, provided there is no free liquid visible at the time the material is loaded or at the time the packaging or transport unit is closed. be marked with the hydrostatic pressure test marking specified in 173.24a(b)(4). (See 173.50 of this subchapter.). 238 Neutron radiation detectors: Neutron radiation detectors containing non-pressurized boron trifluoride gas in excess of 1 gram (0.035 ounces) and radiation detection systems containing such neutron radiation detectors as components may be transported by highway, rail, vessel, or cargo aircraft in accordance with the following: a. If you have comments or suggestions on how to improve the www.ecfr.gov website or have questions about using www.ecfr.gov, please choose the 'Website Feedback' button below. When portable tank instruction T75 is referenced in Column (7) of the 172.101 Table, the applicable refrigerated liquefied gases are authorized to be transported in portable tanks in accordance with the requirements of 178.277 of this subchapter. This is in response to your November 18, 2015 e-mail and subsequent conversations with members of my staff requesting clarification of the Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180) applicable to the selection of a . 346 Nitrogen, refrigerated liquid (cryogenic liquid), UN1977 transported in accordance with the requirements for open cryogenic receptacles in 173.320 and this special provision are not subject to any other requirements of this subchapter. B80 Each cargo tank must have a minimum design pressure of 276 kPa (40 psig). TP47 The 2.5 year internal examination may be waived or substituted by other test methods or inspection procedures specified by the competent authority or its authorized body, provided that the portable tank is dedicated to the transport of the organometallic substances to which this tank special provision is assigned. N43 Metal drums are permitted as single packagings only if constructed of nickel or monel. 345 Nitrogen, refrigerated liquid (cryogenic liquid), UN1977 transported in open cryogenic receptacles with a maximum capacity of 1 L are not subject to the requirements of this subchapter. It must not be used for machinery or apparatus for which a proper shipping name already exists in the 172.101 Table. Insulating materials must not promote corrosion to steel when wet. Lead-free Solder Figure 3: Engineer soldering a microcircuit Note, Tin here is the primary metal. A current copy of CGA pamphlet, CGA C-6 must be available at the facility servicing the life-saving appliance. Such packages must be transported on cargo aircraft only. 177 Gasoline, or, ethanol and gasoline mixtures, for use in internal combustion engines (e.g., in automobiles, stationary engines and other engines) must be assigned to Packing Group II regardless of variations in volatility. Ammonia solutions may be transported in rigid or composite plastic IBCs (31H1, 31H2 and 31HZ1) that have successfully passed, without leakage or permanent deformation, the hydrostatic test specified in. 31 Materials which have undergone sufficient heat treatment to render them non-hazardous are not subject to the requirements of this subchapter. B84 Packagings must be protected with non-metallic linings impervious to the lading or have a suitable corrosion allowance for sulfuric acid or spent sulfuric acid in concentration up to 65.25 percent. Batteries must be securely cushioned and packed to prevent shifting which could loosen terminal caps or reorient the terminals to produce short circuits. Shipping papers at all times must reflect a correct current accounting of all cylinders both full and expended. 19 For domestic transportation only, the identification number UN1075 may be used in place of the identification number specified in column (4) of the 172.101 table. Interpretation Response Details. 136 This entry applies only to articles, machinery, and apparatus containing hazardous materials as an integral element of the article, machinery, or apparatus. Lithium ion cells and batteries at a state of charge greater than 30 percent of their rated capacity may only be transported under conditions approved by the Associate Administrator in accordance with the requirements in 49 CFR part 107, subpart H. Guidance and methodology for determining the rated capacity can be found in sub-section 38.3.2.3 of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). In addition, the material also must be covered with an inert gas or the container must be filled with water to the tank's capacity. Examples of such vehicles are cars, motorcycles, trucks, locomotives, scooters, three- and four-wheeled vehicles or motorcycles, lawn tractors, self-propelled farming and construction equipment, boats, and aircraft. Column 7: Special provisions. A Shipper of a hazardous material is responsible for its classification and packaging prior to offering it for shipment to a Carrier. B69 Dry sodium cyanide or potassium cyanide may be shipped in the following sift-proof and weather-resistant packagings: metal covered hopper cars, covered motor vehicles, portable tanks, or non-specification bins. 33 Ammonium nitrites and mixtures of an inorganic nitrite with an ammonium salt are prohibited. B78 Tank cars must have a test pressure of 4.14 Bar (60 psig) or greater and conform to Class 103, 104, 105, 109, 111, 112, 114 or 120. Tank cars marked HYDROCYANIC ACID prior to October 1, 1991 do not need to be remarked. The rechargeable lithium ion cells can only be charged from the primary lithium metal cells; ii. TP45 Each portable tank must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of 173.24b(b) of this subchapter. d. The proper shipping name Printing ink related material may be used for consignments of packages containing Printing ink and Printing ink related material in the same package. j. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. The eCFR is displayed with paragraphs split and indented to follow Column 7 specifies codes for special provisions applicable to hazardous materials. 5. When a special provision specifies packaging or packaging requirements - Nickel-metal hydride button cells or nickel-metal hydride cells or batteries packed with or contained in battery-powered devices transported by vessel are not subject to the requirements of this special provision. For this test, the provisions of paragraphs 16.6.1.2 except letter g, 16.6.1.3.1 to 16.6.1.3.6, 16.6.1.3.7(b) and 16.6.1.3.8 of the UN Manual of Tests and Criteria must be applied. For transportation by aircraft, as an inner packaging of a combination packaging with a maximum gross mass of 30 kg when packaged as a limited quantity in accordance with 173.27(f). When chemical stabilization is employed, the person offering the material for transport shall ensure that the level of stabilization is sufficient to prevent the material as packaged from dangerous polymerization at 50 C (122 F). The packaging shall be designed for a working temperature of at least 121 C (250 F). For transportation by aircraft, the provisions of 173.159(b)(2) apply. The batteries inside the cargo transport unit are not subject to marking or labelling requirements of part 172 subparts D and E of this subchapter. b. N85 Packagings certified at the Packing Group I performance level may not be used. The Associate Administrator may except from the requirements of this subchapter articles, machinery, and apparatus provided: a. 39 This substance may be carried under provisions other than those of Class 1 only if it is so packed that the percentage of water will not fall below that stated at any time during transport. Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material.

Inbreeding In Northern Ireland, Sims 4 Faster University Mod, Articles C